1)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41486)
Posted 3210 days ago by 5pot That was some good info. I personally always have a hard time swallowing how expensive sone of those boards get. Those they're for benching, but still. I'm sorely trying to wait til Pascal before I do my next actual build. I really should sell some parts though, I've got too many old ones just laying around. They get so inefficient here so quick. |
2)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41358)
Posted 3230 days ago by 5pot E: unless there's a way I can make it stop getting tasks through the website I suppose. Thank you for reminding me of this, changed it when you posted. I've got it clocked down to 1375 for the 2 weeks I'll be away. Want to make sure I don't lose that much crunching time for an OC. @Localizer, these cards can do really well. Good luck with the fine tuning of your card. @Dupont, thanks for the shout out. :) When I get back, I'll try and hit 1500. But I'm beginning to think I'll need to overvolt a little more than I would like to run it permentantly at. But it's always fun to see where the max is. |
3)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41318)
Posted 3233 days ago by 5pot Well, I tried to hit 1500, and walked away for the night. Whoops. Lol. Won't be able to stop it til tomorrow. I do think with an overvoltage I can make it stable. I had it working fine at 1460 without an overvolt. C'est la vie E: unless there's a way I can make it stop getting tasks through the website I suppose. |
4)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41310)
Posted 3233 days ago by 5pot @localizer. I'm surprised you're losing WUs above 1400. I'm sitting at over 1450 now, and still think I may be able to push higher. Do you have a reference card, or one with better cooling? So far, I'm rather impressed with the clocks these can achieve on a minimal to no voltage increase. |
5)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41306)
Posted 3234 days ago by 5pot Just to get back to you, the memory is at 3505MHz. |
6)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41301)
Posted 3234 days ago by 5pot With swan sync on, Gerald was actually 81%. Memory default I'll have to look at when I get back home, and I don't remember noelia usage. I'm going to Japan for 2 weeks on monday, so I probably won't be attempting to run 2 tasks til I get back. |
7)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41298)
Posted 3234 days ago by 5pot Enabled swan_sync, took another task off WCG, got 7.26 on Gerard. Over clock is a tad over 1400MHz now with a .12mV voltage increase. |
8)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41289)
Posted 3235 days ago by 5pot By the way, I thought it was SWAN_SYNC=0? Or did that change to 1? |
9)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41286)
Posted 3235 days ago by 5pot Huh, I hadn't even realized swan_sync had to be started again. I remember it wasn't needed for awhile. I'll change that when I get back home. Gerald utilization was around 75%, but the interesting tidbit for me was that the 980ti is doing noelia in around 10k seconds, with my older 680 rig doing them in 18k seconds. Lol |
10)
Message boards :
Graphics cards (GPUs) :
Big Maxwell GM2*0
(Message 41280)
Posted 3236 days ago by 5pot The card is up and running, with a boost clock (from factory) @ 1315MHz. Not bad at all, considering the boost clock listed is 1190. Results will start reporting over-night, and temps are sitting at 60C w/ a 51% fan setting @ 1187mV. This is also with a 780 in slot2 (not running yet). Further, after looking at how fast it's currently crunching, puts a Gerard_FXCXCL in 25k seconds. It's moving at about .004/s. |
Next 10